Contact mdi

Get Free Quote:
Contact Form
sales@
bekosales.com

 Hours:
7:30AM - 5:30PM ET
Monday - Friday

CLEARPOINT®

BEKO Compressed Air Filters

The filter generation with the 3E effect

CLEARPOINT compressed air filters from BEKO Technologies

  Models

CLEARPOINT Activated Carbon Adsorption Towers

With pressure gauge

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure Max. Inlet Temperature
All 140°F 200 psig 120°F
Activated Carbon Filter Adsorbent
Additional Filtration Necessary
Residual Oil Vapor Content Down to 0.003 mg/m3
Max. Inlet Moisture of 30% (dryer required upstream)
Fully Anodized Powder-Coated Aluminum

Drag your finger across the table to scroll

Model Pipe Size Flow Rate (scfm)
V80 3/4" NPT 80
V120 1" NPT 120
V160 1" NPT 160
V220 1-1/2" NPT 220
V320 1-1/2" NPT 320
V440 1-1/2" NPT 440
V580 2" NPT 580
V740 2" NPT 740
V900 2-1/2" NPT 900
V1300 3" Flange 1300
V1600 3" Flange 1600
V2050 4" Flange 2050
V2980 4" Flange 2980
V4000 6" Flange 4000
V5100 6" Flange 5100

* WARNING: Do not use activated carbon adsorption towers downstream of any heated type desiccant dryers!
** Different operating pressures, compressed air temperatures and/or relative humidities will affect efficiency and service life of activated carbon adsorption towers.

Drag your finger across the table to scroll

Operating Pressure (psig) 20 40 60 80 90 100 110 120 130 140 160 180 200 230
Correction Factor 0.30 0.48 0.65 0.82 0.91 1.00 1.09 1.17 1.26 1.35 1.52 1.70 1.87 2.13

CLEARPOINT 3E Flange Coalescing and Particulate Filters

With BEKOMAT and connection kit with differential pressure gauge


CLEARPOINT 3E flanged coalescing and particulate filters from BEKO Technologies

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 200 psig
CLEARPOINT 3E (Energy Efficient Element)
Performance-Optimized Volume Flow Increased By 30%
Validated In Accordance With ISO 12500
BEKOMAT Drain Standard
Fully Anodized Powder-Coated Aluminum

Drag your finger across the table to scroll

Model Pipe Size (ANSI) Flow Rate (scfm) Element Size
L100 4" 1900 88*
L102 4" 2800 88*
L150 6" 3800 88*
L156 6" 6500 88*
L200 8" 7500 88*
L204 8" 9300 88*
L254 10" 13000 88*
L304 12" 21000 88*

* Refer to the following table.

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Oil Vapor Dry Δ Pressure
(psid)
Wet Δ Pressure
(psid)
Approvals
Grade C Coarse 25 µm 5 mg/m3 0.44 0.73 ASME Coded Vessel with "U" Stamp as standard
(CRN Optional)
Grade G General 5 µm 1 mg/m3 0.58 1.74
Grade F Fine 1 µm 0.1 mg/m3 0.73 2.17
Grade S Superfine 0.01 µm 0.01 mg/m3 0.87 2.9
Grade A Activated Carbon 0.01 µm 0.003 mg/m3 1.45

Drag your finger across the table to scroll

Operating Pressure (psig) 20 40 60 80 90 100 110 120 130 140 160 180 200 230
Correction Factor 0.30 0.48 0.65 0.82 0.91 1.00 1.09 1.17 1.26 1.35 1.52 1.70 1.87 2.13

CLEARPOINT Flange Water Separators

With BEKOMAT and connection kit

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 200 psig

Drag your finger across the table to scroll

Model Pipe Size (ANSI) Flow Rate (scfm) Element Size
L100 4" 1900 88W
L102 4" 2800 88W
L150 6" 3800 88W
L156 6" 6500 88W
L200 8" 7500 88W
L204 8" 9300 88W
L254 10" 13000 88W
L304 12" 21000 88W

Drag your finger across the table to scroll

Element Grade Element Type Dry Δ Pressure (psid) Retention Rate
Grade W Water Separator 0.87 99.0%

Drag your finger across the table to scroll

Operating Pressure (psig) 20 40 60 80 90 100 110 120 130 140 160 180 200 230
Correction Factor 0.30 0.48 0.65 0.82 0.91 1.00 1.09 1.17 1.26 1.35 1.52 1.70 1.87 2.13

CLEARPOINT Threaded Activated Carbon Cartridge Filters

With manual ball valve


CLEARPOINT threaded activated carbon cartridge filter from BEKO Technologies

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 232 psig
Activated Carbon Filter Element
Removal of Solid Particles Up To 1 µm
Residual Oil Vapor Content Down To 0.003 mg/m3
Max. Inlet Moisture of 3% (dryer required downstream)
Fully Anodized Powder-Coated Aluminum

Drag your finger across the table to scroll

Model Pipe Size (NPT) Flow Rate (scfm) Element Size
S055 1/2" 80 06V
M010 1" 160 10V
M018 1-1/2" 330 18V

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Δ Pressure (psig)
Grace V Activated Carbon Cartridge 1 µm 0.003 mg/m3 0.54

Drag your finger across the table to scroll

Operating Pressure (psig) 20 40 60 80 90 100 110 120 130 140 160 180 200 230
Correction Factor 0.30 0.48 0.65 0.82 0.91 1.00 1.09 1.17 1.26 1.35 1.52 1.70 1.87 2.13

CLEARPOINT 3E Threaded Coalescing and Particulate Filters

BEKOMAT and connection kit with or without differential pressure gauge


CLEARPOINT 3E threaded coalescing and particulate filter with BEKOMAT drain from BEKO Technologies

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 232 psig
CLEARPOINT 3E (Energy Efficient Element)
Performance-Optimized Volume Flow Increased By 30%
Validated In Accordance With ISO 12500-1 and 3
BEKOMAT 31 and 32 are Standard
Filter for Natural Gas (CNG) On Request
Fully Anodized Powder-Coated Aluminum

Drag your finger across the table to scroll

Model Pipe Size (NPT) Flow Rate (scfm) Element Size
S040 3/8" 25 04*
S045 1/2" 30 04*
S050 1/2" 50 05*
S055 1/2" 80 06*
S075 3/4" 100 07*
S100 1" 125 07*
M010 1" 160 10*
M012 1" 200 12*
M015 1-1/2" 250 15*
M018 1-1/2" 330 18*
M019 1-1/2" 450 20*
M020 2" 500 20*
M022 2" 600 22*
M023 2" 800 23*
M025 2-1/2" 1000 25*
M027 2-1/2" 1300 27*
M030 3" 1500 30*
M032 3" 1900 32*

* Refer to the following table.

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Dry Δ Pressure (psid) Wet Δ Pressure (psid)
Grade C Coarse 25 µm 5 mg/m3 0.44 0.73
Grade G General 5 µm 1 mg/m3 0.58 1.74
Grade F Fine 1 µm 0.1 mg/m3 0.73 2.17
Grade S Superfine 0.01 µm 0.01 mg/m3 0.87 2.90

Drag your finger across the table to scroll

Operating Pressure (psig) 20 40 60 80 90 100 110 120 130 140 160 180 200 230
Correction Factor 0.30 0.48 0.65 0.82 0.91 1.00 1.09 1.17 1.26 1.35 1.52 1.70 1.87 2.13

CLEARPOINT 3E Threaded Coalescing and Particulate Filters

Float drain with or without differential pressure gauge


CLEARPOINT 3E threaded coalescing and particulate filter with float drain from BEKO Technologies

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 232 psig
CLEARPOINT 3E (Energy Efficient Element)
Performance-Optimized Volume Flow Increased By 30%
Validated In Accordance With ISO 12500-1 and 3
Filter for Natural Gas (CNG) On Request
Fully Anodizes Powder-Coated Aluminum

Drag your finger across the table to scroll

Model Pipe Size (NPT) Flow Rate (scfm) Element Size
S040 3/8" 25 04*
S045 1/2" 30 04*
S050 1/2" 50 05*
S055 1/2" 80 06*
S075 3/4" 100 07*
S100 1" 125 07*
M010 1" 160 10*
M012 1" 200 12*
M015 1-1/2" 250 15*
M018 1-1/2" 330 18*
M019 1-1/2" 450 20*
M020 2" 500 20*
M022 2" 600 22*
M023 2" 800 23*
M025 2-1/2" 1000 25*
M027 2-1/2" 1300 27*
M030 3" 1500 30*
M032 3" 1900 32*

* Refer to the following table.

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Dry Δ Pressure (psid) Wet Δ Pressure (psid)
Grade C Coarse 25 µm 5 mg/m3 0.44 0.73
Grade G General 5 µm 1 mg/m3 0.58 1.74
Grade F Fine 1 µm 0.1 mg/m3 0.73 2.17
Grade S Superfine 0.01 µm 0.01 mg/m3 0.87 2.90

Drag your finger across the table to scroll

Operating Pressure (psig) 20 40 60 80 90 100 110 120 130 140 160 180 200 230
Correction Factor 0.30 0.48 0.65 0.82 0.91 1.00 1.09 1.17 1.26 1.35 1.52 1.70 1.87 2.13

CLEARPOINT PN50 Threaded Coalescing and Particulate High Pressure Filters

With BEKOMAT connection kit (drain sold separately), without pressure gauge


CLEARPOINT 3E threaded coalescing and particulate filter with BEKOMAT drain from BEKO Technologies

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 725 psig
CLEARPOINT 3E (Energy Efficient Element)
Performance-Optimized Volume Flow Increased By 30%
Validated In Accordance With ISO 12500-1 and 3
Shown with BEKOMAT 12 CO PN 63 (see Dimensions table)(optional)
Filter for Natural Gas (CNG) On Request
Fully Anodized Powder-Coated Aluminum

Drag your finger across the table to scroll

Model Pipe Size Flow Rate (scfm) Element Size
HP50S040 3/8" 100 04*
HP50S050 1/2" 190 05*
HP50S055 1/2" 300 06*
HP50S075 3/4" 440 07*
HP50M010 1" 600 10*
HP50M012 1" 710 12*
HP50M015 1-1/2" 1000 15*
HP50M018 1-1/2" 1210 18*
HP50M020 2" 1720 20*

* Refer to the following table.

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Oil Vapor Dry Δ Pressure (psid)
Grade C Coarse 25 µm 5 mg/m3 0.54
Grade G General 5 µm 1 mg/m3 0.70
Grade F Fine 1 µm 0.1 mg/m3 0.86
Grade S Superfine 0.1 µm 0.1 mg/m3 1.04
Grade A Activated Carbon 0.1 µm 0.003 mg/m3 0.70

Drag your finger across the table to scroll

Operating Pressure (psig) 60 90 100 150 200 300 450 600 725
Correction Factor 0.14 0.18 0.24 0.35 0.43 0.59 0.73 0.88 1.00

CLEARPOINT PN50 Threaded Coalescing and Particulate High Pressure Filters

With open port, without pressure gauge


CLEARPOINT PN50 threaded coalescing and particulate high pressure filter with open port, but without pressure gauge, from BEKO Technologies

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 725 psig
CLEARPOINT 3E (Energy Efficient Element)
Performance-Optimized Volume Flow Increased By 30%
Validated In Accordance With ISO 12500-1 and 3
Fully Anodized Powder-Coated Aluminum

Drag your finger across the table to scroll

Model Pipe Size (NPT) Flow Rate (scfm) Element Size
HP50S040 3/8" 100 04*
HP50S050 1/2" 190 05*
HP50S055 1/2" 300 06*
HP50S075 3/4" 440 07*
HP50M010 1" 600 10*
HP50M012 1" 710 12*
HP50M015 1-1/2" 1000 15*
HP50M018 1-1/2" 1210 18*
HP50M020 2" 1720 20*

* Refer to the following table.

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Oil Vapor Dry Δ Pressure (psid)
Grade C Coarse 25 µm 5 mg/m3 0.54
Grade G General 5 µm 1 mg/m3 0.70
Grade F Fine 1 µm 0.1 mg/m3 0.86
Grade S Superfine 0.1 µm 0.1 mg/m3 1.04
Grade A Activated Carbon 0.1 µm 0.003 mg/m3 0.70

Drag your finger across the table to scroll

Operating Pressure (psig) 60 90 100 150 200 300 450 600 725
Correction Factor 0.14 0.18 0.24 0.35 0.43 0.59 0.73 0.88 1.00

CLEARPOINT HP High Pressure Filters

With open port, without pressure gauge, up to 1,450 psig

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Inlet Pressure
All 248°F 1,450 psig
Stainless Steel Housing

Drag your finger across the table to scroll

Model Max. Operating Pressure (psig) Pipe Size (NPT) Flow Rate (scfm)
HP100S040 1,450 3/8" 25
HP100S045 1,450 3/8" 60
HP100S050 1,450 1/2" 160
HP100S055 1,450 1/2" 270
HP100S075 1,450 3/4" 400
HP100M010 1,450 1" 700
HP100M015 1,450 1-1/2" 1000
HP100M020 1,450 2" 2000

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Oil Vapor Dry Δ Pressure (psid)
Grade C Coarse 25 µm 5 mg/m3 0.54
Grade G General 5 µm 1 mg/m3 0.70
Grade F Fine 1 µm 0.1 mg/m3 0.86
Grade S Superfine 0.1 µm 0.1 mg/m3 1.04
Grade A Activated Carbon 0.1 µm 0.003 mg/m3 0.70

Drag your finger across the table to scroll

Operating Pressure (psig) 300 450 600 725 900 1,100 1,200 1,300 1,450
Correction Factor 0.45 0.56 0.64 0.71 0.78 0.84 0.90 0.95 1.00

CLEARPOINT HP High Pressure Filters

With open port, without pressure gauge, up to 5,075 psig

Drag your finger across the table to scroll

Models Max. Operating Temperature HP350S075 / HP350M010
Max. Permissible Operating Temp.
Max. Inlet Pressure
All 248°F 140°F 1,450 psig
Stainless Steel Housing

Drag your finger across the table to scroll

Model Max. Operating Pressure (psig) Pipe Size (NPT) Flow Rate (scfm)
HP350S030 5,075 1/4" 30
HP350S040 5,075 3/8" 75
HP350S045 5,075 3/8" 205
HP350S050 5,075 1/2" 350
HP350S075 5,075 3/4" 520
HP350M010 5,075 1" 920
HP350M012 5,075 1" 1300
HP350M015 5,075 1-1/2" 2600

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Oil Vapor Dry Δ Pressure (psid)
Grade C Coarse 25 µm 5 mg/m3 0.54
Grade G General 5 µm 1 mg/m3 0.70
Grade F Fine 1 µm 0.1 mg/m3 0.86
Grade S Superfine 0.1 µm 0.1 mg/m3 1.04
Grade A Activated Carbon 0.1 µm 0.003 mg/m3 0.70

Drag your finger across the table to scroll

Operating Pressure (psig) 3,000 3,600 4,500 5,075
Correction Factor 0.84 0.89 0.94 1.00

CLEARPOINT HP High Pressure Filters

With open port, without pressure gauge, up to 7,250 psig

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Inlet Pressure
All 248°F 7,250 psig
Stainless Steel Housing

Drag your finger across the table to scroll

Model Max. Operating Pressure (psig) Pipe Size (NPT) Flow Rate (scfm)
HP500S030 7,250 1/4" 30
HP500S040 7,250 3/8" 80
HP500S045 7,250 3/8" 220
HP500S050 7,250 1/2" 380

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Oil Vapor Dry Δ Pressure (psid)
Grade C Coarse 25 µm 5 mg/m3 0.54
Grade G General 5 µm 1 mg/m3 0.70
Grade F Fine 1 µm 0.1 mg/m3 0.86
Grade S Superfine 0.1 µm 0.1 mg/m3 1.04
Grade A Activated Carbon 0.1 µm 0.003 mg/m3 0.70

Drag your finger across the table to scroll

Operating Pressure (psig) 4,500 5,000 5,800 6,500 7,250
Correction Factor 0.89 0.93 0.96 0.98 1.00

CLEARPOINT H Compressed Air Heaters

With adjustable temperature control

Drag your finger across the table to scroll

For the Adjustable Heating of Compressed Air (max. 232 psig)
Ready for Connection With a Three-Prong Plug
Encapsulated Corrosion-Free Stainless Steel Heating Cartridges
Temperature Adjustable From +86 to +140°F
Available Touch Protection Option
Fully Anodized Powder-Coated Aluminum

Drag your finger across the table to scroll

CLEARPOINT H S040 S050
Pipe Size (NPT) 3/8" 1/2"
Max. Volume Flow at 100 psig 30 scfm 60 scfm
Setting Ranged Compressed-Air Outlet Temperature (°F)* +86 - +140 +86 - +140
Max. Perm. Operating Overpressure (psig) 232 232
Pressure Difference < 2.18 psig < 2.90 psig
Voltage** 115 VAC / 60 Hz +/-10% 115 VAC / 60 Hz +/-10%
Inlet Temperature (°F) +36 - +122 +36 - +122
Ambient Temperature (°F) +36 - +122 +36 - +122
Internal Safety Switch-Off Temperature (°F) +183 +183
Max. Housing Temperature (°F) +176 +176
Max. Compressed-Air Outlet Temperature (°F)* +140 +140
Power (W)*** 420 (750) 420 (750)
Volume (l) 0.42 0.42
Protection Class IP 54 IP 54

* Depending on volume flow
** Other voltages on request
*** At +68°F: making current max. 4 A, making capacity max. 750 W


CLEARPOINT Threaded Water Separators

With BEKOMAT and connection kit


CLEARPOINT threaded water separator with BEKOMAT drain from BEKO Technologies

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 232 psig

Drag your finger across the table to scroll

Model Pipe Size (NPT) Flow Rate (scfm) Element Size
S040 3/8" 25 04W
S045 1/2" 30 04W
S050 1/2" 50 05W
S075 3/4" 100 07W
S0100 1" 125 07W
M010 1" 160 10W
M015 1-1/2" 250 15W
M019 1-1/2" 450 20W
M020 2" 500 20W
M022 2-1/2" 600 22W
M025 2-1/2" 1000 25W
M030 3" 1500 30W

Drag your finger across the table to scroll

Element Grade Element Type Δ Pressure (psid) Retention Rate
Grade W Water Separator 0.87 99.0%

Drag your finger across the table to scroll

Operating Pressure (psig) 20 40 60 80 90 100 110 120 130 140 160 180 200 230
Correction Factor 0.30 0.48 0.65 0.82 0.91 1.00 1.09 1.17 1.26 1.35 1.52 1.70 1.87 2.13

CLEARPOINT Threaded Water Separators

With float drain


CLEARPOINT threaded water separator with float drain from BEKO Technologies

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 232 psig

Drag your finger across the table to scroll

Model Pipe Size (NPT) Flow Rate (scfm) Element Size
S040 3/8" 25 04W
S045 1/2" 30 04W
S050 1/2" 50 05W
S075 3/4" 100 07W
S0100 1" 125 07W
M010 1" 160 10W

Drag your finger across the table to scroll

Element Grade Element Type Δ Pressure (psid) Retention Rate
Grade W Water Separator 0.87 99.0%

Drag your finger across the table to scroll

Operating Pressure (psig) 20 40 60 80 90 100 110 120 130 140 160 180 200 230
Correction Factor 0.30 0.48 0.65 0.82 0.91 1.00 1.09 1.17 1.26 1.35 1.52 1.70 1.87 2.13

CLEARPOINT PN50 Threaded High Pressure Water Separators

With open port or with BEKOMAT connection kit (drain sold separately), without pressure gauge


CLEARPOINT PN50 threaded high pressure water separator from BEKO Technologies

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 725 psig

Drag your finger across the table to scroll

Model Pipe Size (NPT) Flow Rate (scfm) Element Size
HP50S040 3/8" 100 04W
HP50S050 1/2" 190 05W
HP50S075 3/4" 440 07W
HP50M010 1" 600 10W
HP50M015 1-1/2" 1000 15W
HP50M020 2" 1720 20W

Drag your finger across the table to scroll

Element Grade Element Type Δ Pressure (psid) Retention Rate
Grade W Water Separator 0.87 99.0%

Drag your finger across the table to scroll

Operating Pressure (psig) 60 90 100 150 200 300 450 600 725
Correction Factor 0.14 0.18 0.24 0.35 0.43 0.59 0.73 0.88 1.00

CLEARPOINT PN50 Threaded Vapor Removal High Pressure Filters

With manual ball valve, without pressure gauge

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 725 psig
Activated Carbon Filter Element
Removal of Solid Particles Up To 0.01 µm
Residual Oil Vapor Content Down To 0.003 mg/m3
Max. Inlet Moisture of 30% (dryer required upstream)
Fully Anodized Powder-Coated Aluminum

Drag your finger across the table to scroll

Model Pipe Size Flow Rate (scfm) Element Size
HP50S040 3/8" 100 04A
HP50S050 1/2" 190 05A
HP50S055 1/2" 300 06A
HP50S075 3/4" 440 07A
HP50M010 1" 600 10A
HP50M012 1" 710 12A
HP50M015 1-1/2" 1000 15A
HP50M018 1-1/2" 1210 18A
HP50M020 2" 1720 20A

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Oil Vapor Dry Δ Pressure (psid)
Grade A Activated Carbon 0.01 µm 0.003 mg/m3 0.70

Drag your finger across the table to scroll

Operating Pressure (psig) 60 90 100 150 200 300 450 600 725
Correction Factor 0.14 0.18 0.24 0.35 0.43 0.59 0.73 0.88 1.00

CLEARPOINT Threaded Vapor Removal Filters

With manual ball valve

Drag your finger across the table to scroll

Models Max. Operating Temperature Max. Operating Pressure
All 140°F 232 psig
Activated Carbon Filter Element
Removal of Solid Particles Up To 0.01 µm
Residual Oil Vapor Content Down To 0.003 mg/m3
Max. Inlet Moisture of 30% (dryer required downstream)
Fully Anodized Powder-Coated Aluminum

Drag your finger across the table to scroll

Model Pipe Size (NPT) Flow Rate (scfm) Element Size
S040 3/8" 25 04A
S045 1/2" 30 04A
S050 1/2" 50 05A
S055 3/4" 80 06A
S075 3/4" 100 07A
S100 1" 125 07A
M010 1" 160 10A
M012 1" 200 12A
M015 1-1/2" 250 15A
M018 1-1/2" 330 18A
M019 1-1/2" 450 20A
M020 2" 500 20A
M022 2" 600 22A
M023 2" 800 23A
M025 2-1/2" 1000 25A
M027 2-1/2" 1300 27A
M030 3" 1500 30A
M032 3" 1900 32A

Drag your finger across the table to scroll

Element Grade Element Type Micron Rating Oil Carryover Dry Δ Pressure (psid)
Grade A Activated Carbon 0.01 µm 0.003 mg/m3 1.02

Drag your finger across the table to scroll

Operating Pressure (psig) 20 40 60 80 90 100 110 120 130 140 160 180 200 230
Correction Factor 0.30 0.48 0.65 0.82 0.91 1.00 1.09 1.17 1.26 1.35 1.52 1.70 1.87 2.13

  Features

The CLEARPOINT Principle

  • Energy Efficient Elements (3E): all 3E element design made of sintered borosilicate fibers for ultra low differential pressure
  • Flow Optimized Housing: the unique curved inlet design was engineered to provide the lowest possible differential pressure
  • Maximum Reliability: double threaded filter head, extruded, fully anodized sea-water resistant housing, and zero loss drain option
  • Comprehensive Line: from 25 to 50,000 scfm and up to 7,250 psi
  • Simplified Maintenance: simple, push-fit element design without the use of tie-rods and integrated housing safety latch with audible alarm

During compressed air generation and processing, the optimum quality for the respective application should be achieved. The most important target is to remove contaminants, humidity and oil from the compressed air, as these can lead to a deterioration in quality, machine failure, or even to a loss of production or to products that cannot be used.

Contaminants in compressed air
The generation of compressed air always involves some form of contamination. In most cases, the air stream contains oil and unwanted particles that disperse over the entire compressed air network. This is a system wide problem that will cause damage and cause costs to increase. In addition, contamination does not accumulate at regular intervals, but varies depending on the climate, temperature, season, time of day and even the capacity utilization of the compressor. Therefore, it is best to always be protected for the worst case scenario.

3E Effect
BEKO Technologies uses new 3E filter material for all filter elements. This increases the lifetime and efficiency up to 30%.

Operating Principle - Flanged Filters


Diagram showing the operating principle for CLEARPOINT flanged filters from BEKO Technologies

[1] Connections
The filter housing has two one-level compressed-air connections enabling easy installation in existing pipeworks.


[2] Differential Pressure Gauge
To be able to also optically monitor the contamination degree of the filter elements when the housings are closed, all filters can be optionally equipped with a differential manometer which is readable from both sides. The scaled indication can be used for the direct energy-cost analysis.


[3] Housings
BEKO Technologies flanged-filter housings receive full-bath galvanising according to the high-temperature method. Prior to the galvanising process, the housings are subject to alkaline degreasing and pickling, which results in high-grade inside and outside surface protection.


[4] Easy to Maintain
As regards the CLEARPOINT flanged filters, the replacement of filter elements is easily undertaken from the top. The inconvenient dismantling of condensate drains is therefore no longer necessary. To open the filter housing, only the upper blank flange is loosened, except for one remaining flange screw which is then used like a pivot joint. In smaller device sizes, the blank flange can easily be fullyremoved.


[5] Filter Element
The large surface of the filter elements reduces the air velocity to energeticallyfavourable values. The cavity volume of the polyfibre filter material of 98% ensures lowest pressure loss. With this, the crosssectional area free for the through-flow is many times larger in CLEARPOINT filters.


[6] Installation Option
As an alternative to usually suspended mounting, the housing can also be set up vertically. Seat plates welded-on radially enable the optional mounting of feet which can be anchored on the floor.


Operating Principle - Threaded Filters


Diagram showing the operating principle for CLEARPOINT threaded filters from BEKO Technologies

[1] Connections
The threaded end fittings of the CLEARPOINT compressed air filters are, compared with those of other filter brands, generously dimensioned and constructionally optimally aligned with the connections of the different compressor manufacturers. Energy-guzzling constrictions are therefore a thing of the past. Through the innovative connection method, the full cross-section will also be maintained when combining several CLEARPOINT compressed-air filters.


[2] Filter Elements
CLEARPOINT 3E filter elements and cartridges are designed without the use of cross-section-reducing and tension disturbing anchors. They are flow resistance optimized in both flow directions from inside / out and outside / in. The innovative push-fit design of the elements allows easy and fast replacement, and the sintered borosilicate fibers extend the element lifetime.


[3] More Profitability
Up to 75% less flow resistance; more profitability. The flow optimized, curved inlet saves energy costs.


[4] Increased Safety
The safe shutter mechanism offers a 100% control when opening the filter housing. In the event that the housing is opened under pressure, a warning signal sounds. The shutter mechanism also prevents unlatching during vibrations.


[5] Effective Corrosion Protection
Condensate accumulating during compressed-air filtration is almost always aggressive, so that unprotected housings corrode. CLEARPOINT filter housings are made of saltwater-proof aluminum and, in addition, are fully anodized. This increases the operational safety because corrosion cannot develop on the clean-air side; the ultimate consumer is therefore protected. Moreover, the permanently smooth surface reduces the flow resistance.


[6] Ease of Maintenance
A hexagonal profile has been included in the design of the filter housing allowing it to be easily opened for element changes.


[7] Condensate Collecting Zone
A generously-dimensioned condensate collecting zone prevents the entrainment of already separated condensate.


Operating Principle - Water Separators


Diagram showing the operating principle for CLEARPOINT water separators from BEKO Technologies

[1] Connections
The connections are perfectly matched to the outlet of the compressor. The flow-optimized inlet leads to reduced flow resistance.


[2] Internal Swirl Insert
When the compressed air has entered the CLEARPOINT water separator housing, it reaches a special internal swirl insert that makes the entering compressed air flow experience a special rotary motion with high velocity. The consequence: the outwardly directed rotational forces lead the condensate droplets to the separator wall, from where they flow into the collecting zone.


[3] Effective Corrosion Protection
Condensate accumulating during compressed air filtration is almost always aggressive, so that unprotected housings corrode. CLEARPOINT water separator filter housings are made of saltwater proof aluminum and, in addition, are fully anodized and their outside is powder coated.


[4] Increased Safety
The safe shutter mechanism offers a 100% control when opening the filter housing. In the event that the housing is opened under pressure, a warning signal sounds. The shutter mechanism also prevents unlatching during vibrations.


[5] Rising Pipe
A specially designed rising pipe avoids particle transfer to the upwardly directed rotational flow of the already purified compressed air.


[6] Rectifier
The innovative rectifier leads the compressed air to the outlet and reduces flow losses to a minimum.


[7] Shielded Collecting Zone
The shielding of the collecting zone settles the air flow in this area in order to effectively avoid the dispersion and re-entrainment of already separated liquids.


[8] BEKOMAT
More than 60% of the total amount of condensate already accumulates in the water separator. The electronically level controlled BEKOMAT ensures reliable drainage.


  Dimensions

CLEARPOINT Activated Carbon Adsorption Towers

With pressure gauge


Drawing showing the dimensions of a CLEARPOINT activated carbon adsorption tower from BEKO Technologies

Drag your finger across the table to scroll

Model A B C Weight
V80 63 in 12 in 20 in 190 lbs
V120 63 in 14 in 20 in 196 lbs
V160 63 in 14 in 20 in 224 lbs
V220 81 in 16 in 20 in 260 lbs
V320 81 in 21 in 20 in 312 lbs
V440 81 in 22 in 20 in 380 lbs
V580 86 in 22 in 22 in 460 lbs
V740 86 in 22 in 30 in 600 lbs
V900 86 in 26 in 38 in 720 lbs
V1300 86 in 30 in 42 in 880 lbs
V1600 83 in 35 in 48 in 1480 lbs
V2050 97 in 35 in 48 in 1800 lbs
V2980 104 in 40 in 58 in 2400 lbs
V4000 106 in 54 in 52 in 3040 lbs
V5100 106 in 56 in 60 in 3800 lbs

* WARNING: Do not use activated carbon adsorption towers downstream of any heated type desiccant dryers!
** Different operating pressures, compressed air temperatures and/or relative humidities will affect efficiency and service life of activated carbon adsorption towers.


CLEARPOINT 3E Flange Coalescing and Particulate Filters

With BEKOMAT and connection kit with differential pressure gauge


Drawing showing the dimensions of a CLEARPOINT 3E flanged coalescing and particulate filter from BEKO Technologies

Drag your finger across the table to scroll

Model A B C1 D Weight
L100 21.26 in 6.88 in 45.75 in 13.00 in 130 lbs
L102 23.62 in 6.46 in 46.22 in 18.00 in 185 lbs
L150 23.62 in 7.44 in 48.19 in 18.00 in 217 lbs
L156 25.60 in 7.24 in 48.58 in 18.00 in 232 lbs
L200 27.95 in 8.43 in 50.95 in 18.00 in 295 lbs
L204 30.31 in 8.43 in 51.34 in 18.00 in 378 lbs
L254 34.65 in 9.69 in 54.76 in 18.00 in 552 lbs
L304 38.98 in 10.87 in 57.91 in 18.00 in 776 lbs

CLEARPOINT Flange Water Separators

With BEKOMAT and connection kit


Drawing showing the dimensions of a CLEARPOINT flanged water separator from BEKO Technologies

Drag your finger across the table to scroll

Models A B C1 D Weight
L100 16.73 in 6.54 in 35.83 in 12.40 in 93 lbs
L102 18.90 in 7.80 in 38.19 in 18.90 in 117 lbs
L150 19.10 in 8.35 in 50.79 in 18.90 in 165 lbs
L156 21.06 in 8.74 in 51.58 in 18.50 in 209 lbs
L200 22.83 in 10.95 in 66.14 in 18.31 in 337 lbs
L204 24.80 in 11.34 in 66.93 in 17.72 in 366 lbs
L254 29.53 in 13.07 in 81.50 in 17.72 in 392 lbs
L304 34.25 in 14.57 in 95.28 in 16.93 in 549 lbs

CLEARPOINT Threaded Activated Carbon Cartridge Filters

With manual ball valve


Drawing showing the dimensions of a CLEARPOINT threaded activated carbon cartridge filter from BEKO Technologies

Drag your finger across the table to scroll

Model A C1 D Weight
S055 2.95 in 10.43 in 5.91 in 2.65 lbs
M010 3.94 in 13.78 in 5.91 in 4.63 lbs
M018 5.75 in 16.46 in 6.30 in 9.92 lbs

CLEARPOINT 3E Threaded Coalescing and Particulate Filters

BEKOMAT and connection kit with or without differential pressure gauge


Drawing showing the dimensions of a CLEARPOINT 3E threaded coalescing and particulate filter with BEKOMAT drain from BEKO Technologies

Drag your finger across the table to scroll

Model A C1 C2 D Weight
S040 2.95 in 15.55 in 18.11 in 5.91 in 1.65 lbs
S045 2.95 in 15.55 in 18.11 in 5.91 in 1.65 lbs
S050 2.95 in 16.73 in 19.29 in 5.91 in 1.87 lbs
S055 2.95 in 18.90 in 21.46 in 5.91 in 2.65 lbs
S075 3.94 in 19.49 in 22.05 in 5.91 in 3.75 lbs
S100 3.94 in 19.49 in 22.05 in 5.91 in 4.18 lbs
M010 3.94 in 22.24 in 24.80 in 5.91 in 4.63 lbs
M012 3.94 in 23.62 in 26.18 in 5.91 in 4.85 lbs
M015 5.75 in 22.83 in 25.39 in 6.30 in 9.04 lbs
M018 5.75 in 24.92 in 27.48 in 6.30 in 9.92 lbs
M019 5.75 in 26.89 in 29.45 in 6.30 in 10.61 lbs
M020 5.75 in 26.89 in 29.45 in 6.30 in 11.24 lbs
M022 5.75 in 30.71 in 33.27 in 6.30 in 13.45 lbs
M023 5.75 in 35.35 in 37.91 in 6.30 in 15.65 lbs
M025 10.24 in 34.88 in 37.44 in 7.87 in 43.87 lbs
M027 10.24 in 38.98 in 41.54 in 7.87 in 49.82 lbs
M030 10.24 in 39.76 in 42.32 in 7.87 in 57.10 lbs
M032 10.24 in 49.61 in 52.17 in 7.87 in 65.92 lbs

CLEARPOIN 3E Threaded Coalescing and Particulate Filters

Float drain with or without differential pressure gauge


Drawing showing the dimensions of a CLEARPOINT 3E threded coalescing and particulate filter with float drain from BEKO Technologies

Drag your finger across the table to scroll

Model A C1 C2 D Weight
S040 2.95 in 7.09 in 9.65 in 5.91 in 1.65 lbs
S045 2.95 in 7.09 in 9.65 in 5.91 in 1.65 lbs
S050 2.95 in 8.27 in 10.83 in 5.91 in 1.87 lbs
S055 2.95 in 10.43 in 12.99 in 5.91 in 2.65 lbs
S075 3.94 in 11.02 in 13.58 in 5.91 in 3.75 lbs
S100 3.94 in 11.02 in 13.58 in 5.91 in 4.18 lbs
M010 3.94 in 13.78 in 16.34 in 5.91 in 4.63 lbs
M012 3.94 in 15.16 in 17.72 in 5.91 in 4.85 lbs
M015 5.75 in 14.17 in 16.73 in 6.30 in 9.04 lbs
M018 5.75 in 16.46 in 19.02 in 6.30 in 9.92 lbs
M019 5.75 in 18.43 in 20.99 in 6.30 in 10.61 lbs
M020 5.75 in 18.43 in 20.99 in 6.30 in 11.24 lbs
M022 5.75 in 22.24 in 24.80 in 6.30 in 13.45 lbs
M023 5.75 in 26.89 in 29.45 in 6.30 in 15.65 lbs
M025 10.24 in 26.42 in 29.98 in 7.87 in 43.87 lbs
M027 10.24 in 30.51 in 33.07 in 7.87 in 49.82 lbs
M030 10.24 in 35.24 in 37.80 in 7.87 in 57.10 lbs
M032 10.24 in 41.14 in 43.70 in 7.87 in 65.92 lbs

CLEARPOINT PN50 Threaded Coalescing and Particulate High Pressure Filters

With BEKOMAT connection kit (drain sold separately), without pressure gauge


Drawing showing the dimensions of a CLEARPOINT PN50 threaded coalescing and particulate high pressure filter from BEKO Technologies

Drag your finger across the table to scroll

Model A A1 C1 C2 D Weight
HP50S040 2.95 in 2.36 in 16.50 in 7.10 in 7.10 in 1.65 lbs
HP50S050 2.95 in 2.36 in 16.50 in 8.30 in 7.10 in 1.85 lbs
HP50S055 2.95 in 2.36 in 19.90 in 10.40 in 7.10 in 2.65 lbs
HP50S075 3.95 in 3.15 in 20.50 in 11.00 in 7.10 in 3.75 lbs
HP50M010 3.95 in 3.15 in 23.20 in 13.80 in 7.10 in 4.63 lbs
HP50M012 3.95 in 3.15 in 24.60 in 15.20 in 7.10 in 4.85 lbs
HP50M015 5.75 in 4.72 in 23.80 in 14.40 in 7.10 in 9.04 lbs
HP50M018 5.75 in 4.72 in 25.90 in 16.50 in 7.10 in 9.92 lbs
HP50M020 5.75 in 4.72 in 27.80 in 18.40 in 7.10 in 11.24 lbs

CLEARPOINT PN50 Threaded Coalescing and Particulate High Pressure Filters

With open port, without pressure gauge


Drawing showing the dimensions of a CLEARPOINT PN50 threaded coalescing and particulate high pressure filter with an open port, but without a pressure gauge, from BEKO Technologies

Drag your finger across the table to scroll

Model A A1 C1 Weight
HP50S040 2.95 in 2.36 in 7.10 in 1.65 lbs
HP50S050 2.95 in 2.36 in 8.30 in 1.85 lbs
HP50S055 2.95 in 2.36 in 10.40 in 2.65 lbs
HP50S075 3.95 in 3.15 in 11.00 in 3.75 lbs
HP50M010 3.95 in 3.15 in 13.80 in 4.63 lbs
HP50M012 3.95 in 3.15 in 15.20 in 4.85 lbs
HP50M015 5.75 in 4.72 in 14.40 in 9.04 lbs
HP50M018 5.75 in 4.72 in 16.50 in 9.92 lbs
HP50M020 5.75 in 4.72 in 18.40 in 11.24 lbs

CLEARPOINT HP High Pressure Filters

With open port, without pressure gauge, up to 1,450 psig


Drawing showing the dimensions of a CLEARPOINT HP high pressure filter with open port, but without pressure gauge, from BEKO Technologies

Drag your finger across the table to scroll

Model A B C E Volume Weight
HP100S040 2.36 in 0.65 in 4.61 in 0.98 in 0.01 gal 4.41 lbs
HP100S045 3.11 in 0.81 in 5.51 in 1.39 in 0.03 gal 9.92 lbs
HP100S050 3.07 in 0.91 in 8.43 in 1.57 in 0.10 gal 8.82 lbs
HP100S055 3.07 in 0.91 in 10.39 in 1.57 in 0.13 gal 12.13 lbs
HP100S075 4.49 in 1.16 in 10.63 in 2.36 in 0.32 gal 23.15 lbs
HP100M010 4.49 in 1.16 in 16.54 in 2.36 in 0.52 gal 30.20 lbs
HP100M015 6.85 in 1.97 in 18.94 in 3.94 in 0.87 gal 74.96 lbs
HP100M020 6.85 in 1.97 in 30.87 in 3.94 in 1.51 gal 92.60 lbs

CLEARPOINT HP High Pressure Filters

With open port, without pressure gauge, up to 5,075 psig


Drawing showing the dimensions of a CLEARPOINT HP high pressure filter with open port, but without pressure gauge, from BEKO Technologies

Drag your finger across the table to scroll

Model A B C E Volume Weight
HP350S030 2.36 in 0.65 in 4.61 in 0.98 in 0.01 gal 4.41 lbs
HP350S040 3.11 in 0.81 in 5.51 in 1.39 in 0.03 gal 9.92 lbs
HP350S045 3.46 in 0.91 in 8.43 in 1.57 in 0.10 gal 14.33 lbs
HP350S050 3.46 in 0.91 in 10.39 in 1.57 in 0.13 gal 16.53 lbs
HP350S075 5.47 in 1.47 in 11.26 in 3.15 in 0.30 gal 45.19 lbs
HP350M010 5.47 in 1.47 in 17.17 in 3.15 in 0.52 gal 59.52 lbs
HP350M012 6.65 in 1.94 in 18.90 in 3.15 in 0.85 gal 99.23 lbs
HP350M015 6.65 in 1.94 in 30.83 in 3.15 in 1.51 gal 156.53 lbs

CLEARPOINT HP High Pressure Filters

With open port, without pressure gauge, up to 7,250 psig


Drawing showing the dimensions of a CLEARPOINT HP high pressure filter with open port, but without pressure gauge, from BEKO Technologies

Drag your finger across the table to scroll

Model A B C E Volume Weight
HP500S030 2.36 in 0.65 in 4.61 in 0.98 in 0.01 gal 4.41 lbs
HP500S040 3.11 in 0.81 in 5.51 in 1.39 in 0.03 gal 9.92 lbs
HP500S045 4.45 in 0.98 in 8.70 in 2.36 in 0.10 gal 26.46 lbs
HP500S050 4.45 in 0.98 in 10.67 in 2.36 in 0.13 gal 28.66 lbs

CLEARPOINT H Compressed Air Heaters

With adjustable temperature control


Drawing showing the dimensions of a CLEARPOINT H compressed air heater from BEKO Technologies

NOTE: Above measurements are in inches.


Drag your finger across the table to scroll

CLEARPOINT H S040 S050
Weight (lbs) 5.3 5.3

CLEARPOINT Threaded Water Separators

With BEKOMAT and connection kit


Drawing showing the dimensions of a CLEARPOINT threaded water separator with BEKOMAT drain from BEKO Technologies

Drag your finger across the table to scroll

Model A C1 D Weight
S040 2.95 in 15.55 in 5.91 in 1.65 lbs
S045 2.95 in 15.55 in 5.91 in 1.65 lbs
S050 2.95 in 16.73 in 5.91 in 1.87 lbs
S075 3.94 in 19.49 in 5.91 in 3.75 lbs
S0100 3.94 in 19.49 in 5.91 in 4.18 lbs
M010 3.94 in 22.24 in 5.91 in 4.63 lbs
M015 5.75 in 22.83 in 6.30 in 9.04 lbs
M019 5.75 in 26.89 in 6.30 in 10.61 lbs
M020 5.75 in 26.89 in 6.30 in 11.24 lbs
M022 5.75 in 30.71 in 6.30 in 13.45 lbs
M025 10.24 in 34.88 in 7.87 in 43.87 lbs
M030 10.24 in 39.76 in 7.87 in 57.10 lbs

CLEARPOINT Threaded Water Separators

With float drain


Drawing showing the dimensions of a CLEARPOINT threaded waters separator with float drain from BEKO Technologies

Drag your finger across the table to scroll

Model A C1 D Weight
S040 2.95 in 7.09 in 5.91 in 1.65 lbs
S045 2.95 in 7.09 in 5.91 in 1.65 lbs
S050 2.95 in 8.27 in 5.91 in 1.87 lbs
S075 3.94 in 11.02 in 5.91 in 3.75 lbs
S0100 3.94 in 11.02 in 5.91 in 4.18 lbs
M010 3.94 in 13.78 in 4.91 in 4.63 lbs

CLEARPOINT PN50 Threaded High Pressure Water Separators

With open port or with BEKOMAT connection kit (drain sold separately), without pressure gauge


Drawing showing the dimensions of two CLEARPOINT PN50 threaded high pressure water separators - one with open port and one with BEKOMAT connection kit, both without pressure gauges - from BEKO Technologies

Drag your finger across the table to scroll

Model A C C1 D Weight
HP50S040 2.95 in 7.10 in 16.50 in 7.10 in 1.65 lbs
HP50S050 2.95 in 8.30 in 16.50 in 7.10 in 1.85 lbs
HP50S075 3.95 in 11.00 in 20.50 in 7.10 in 3.75 lbs
HP50M010 3.95 in 13.80 in 23.20 in 7.10 in 4.63 lbs
HP50M015 5.75 in 14.40 in 23.80 in 7.10 in 9.04 lbs
HP50M020 5.75 in 18.40 in 27.80 in 7.10 in 11.24 lbs

CLEARPOINT PN50 Threaded Vapor Removal High Pressure Filters

With manual ball valve, without pressure gauge


Drawing showing the dimensions of a CLEARPOINT PN50 threaded vapor removal high pressure filter with manual ball valve, but without pressure gauge, from BEKO Technologies

Drag your finger across the table to scroll

Model A A1 B C1 C2 D Weight
HP50S040 2.95 in 2.36 in 1.10 in 16.50 in 7.10 in 7.10 in 1.65 lbs
HP50S050 2.95 in 2.36 in 1.10 in 16.50 in 8.30 in 7.10 in 1.85 lbs
HP50S055 2.95 in 2.36 in 1.10 in 19.90 in 10.40 in 7.10 in 2.65 lbs
HP50S075 3.95 in 3.15 in 1.34 in 20.50 in 11.00 in 7.10 in 3.75 lbs
HP50M010 3.95 in 3.15 in 1.34 in 23.20 in 13.80 in 7.10 in 4.63 lbs
HP50M012 3.95 in 3.15 in 1.34 in 24.60 in 15.20 in 7.10 in 4.85 lbs
HP50M015 5.75 in 4.72 in 1.89 in 23.80 in 14.40 in 7.10 in 9.04 lbs
HP50M018 5.75 in 4.72 in 1.89 in 25.90 in 16.50 in 7.10 in 9.92 lbs
HP50M020 5.75 in 4.72 in 1.89 in 27.80 in 18.40 in 7.10 in 11.24 lbs

CLEARPOINT Threaded Vapor Removal Filters

With manual ball valve


Drawing showing the dimensions of a CLEARPOINT threaded vapor removal filter with manual ball valve from BEKO Technologies

Drag your finger across the table to scroll

Model A C1 D Weight
S040 2.95 in 7.09 in 5.91 in 1.65 lbs
S045 2.95 in 7.09 in 5.91 in 1.65 lbs
S050 2.95 in 8.27 in 5.91 in 1.87 lbs
S055 2.95 in 10.43 in 5.91 in 2.65 lbs
S075 3.94 in 11.02 in 5.91 in 3.75 lbs
S100 3.94 in 11.02 in 5.91 in 4.18 lbs
M010 3.94 in 13.78 in 5.91 in 4.63 lbs
M012 3.94 in 15.16 in 5.91 in 4.85 lbs
M015 5.75 in 14.17 in 6.30 in 9.04 lbs
M018 5.75 in 16.46 in 6.30 in 9.92 lbs
M019 5.75 in 16.46 in 6.30 in 10.61 lbs
M020 5.75 in 18.43 in 6.30 in 11.24 lbs
M022 5.75 in 22.24 in 6.30 in 13.45 lbs
M023 5.75 in 26.89 in 6.30 in 15.65 lbs
M025 10.24 in 26.42 in 7.87 in 43.87 lbs
M027 10.24 in 30.51 in 7.87 in 49.82 lbs
M030 10.24 in 35.24 in 7.87 in 57.10 lbs
M032 10.24 in 41.14 in 7.87 in 65.92 lbs

  Contact mdi

Please fill out the form below and your personal mdi product expert will email you your quote. The more information that you provide the quicker we can send you a quote. Sending an incomplete quote request could mean that we have to contact you for necessary information before sending your quote. And know that our knowledgeable sales staff is standing by to help you with your order and with any questions.






Please include your contact information so that we may reply to your request. Your contact information is private and will not be sold to any third party or used negatively in any way.










mdi does not advertise prices online. The cost of products is subject to change over time. In order to extend to you the best price that we can offer, we prefer to create written and emailed quotes which reflect any discounts or promotions currently available. Some products can be quoted over the phone, and expediting quotes and orders is always available per request.

See our Terms and Conditions for more information about the mdi sales process.


Call us any time Monday through Friday 7:30 AM to 5:30 PM ET.

Phone: (727) 835-0670 | Toll Free: 800-761-4298
Fax: (813) 571-0422 | Email or Fill Out the Form Above